Please Note ... WE AIM TO SHIP THE SAME DAY BUT DUE TO COVID WAREHOUSE RESTRICTION YOUR ORDER MIGHT SHIP THE FOLLOWING DAY . *** Refer to Guides for stock information (no change as from the 8th April 2021) *** Any other enquiry please send email to



VAT already included
Refer to Guides at top of Page

Schiit Mjolnir 2

Schiit Mjolnir 2 is the only balanced tube or solid state headphone amplifier

 The Schiit Mjolnir 2  is the only balanced tube hybrid headphone amplifier using 6BZ7 tubes or our all new LISST solid state tube option. 

Choose Tube Hybrid, Solid-State, or Both

Yes, that's right. You can get the Schiit Mjolnir 2 as a tube hybrid, or as a pure solid-state amp or get both, and swap out as you like. You can also swap the standard 6BZ7 tubes for anything in the 6DJ8, 6922, ECC88, and 2492 families, to tube roll the sound to your specific preference. Or just opt for the Schiit LISST (Linear, Integral Solid-State Tube) for a 100% solid state amp. 

Schiit Mjolnir 2 puts out up to 8W a channel into 32 ohms, but is fully ready for high-sensitivity headphones with switchable gain. Use the standard gain of 8 for hard-to-drive headphones, or switch to a gain of 1 for sensitive on-ear models and IEMs. In addition, Mjolnir 2 also offers both balanced and single-ended input, switchable via the front panel. Want more? How about both balanced and single-ended headphone outputs and balanced and single-ended preamp outputs. Mjolnir also makes a great preamp for your power amps or powered monitors.

Pure Balanced, Differential Topology

Schiit's Mjolnir uses our exclusive, inherently balanced and differential Crossfet topology the only circlotron-style topology in a headphone amplifier (well, except for Ragnarok). It's balanced in and balanced out, with a custom 4-gang RK27 Alps volume pot providing end-game performance for a mid-level price.

Most of the Schiit Mjolnir 2  is covered by a limited warranty that covers parts and labour for four years. That's 4 years. Yes Four. Compare that to the competition. The parts that are not covered by a 4-year warranty: the tubes. Tubes are covered by a 28-day warranty. They should last between 3,000 and 5,000 hours. Please note this doesn't mean free upgrades!

Frequency Response: 20Hz-20Khz, -0.1db, 2Hz-400KHz, -3dB

Maximum Power, 32 ohms: 8W RMS per channel

Maximum Power, 50 ohms: 5W RMS per channel

Maximum Power, 300 ohms: 850mW RMS per channel

Maximum Power, 600 ohms: 425mW RMS per channel

THD: Less than 0.005%, 20Hz-20KHz, at 1V RMS

IMD: Less than 0.006%, CCIF at 1V RMS

SNR: Greater than 104db, unweighted, referenced to 1V RMS in low gain mode

Crosstalk: -75dB, 20 Hz-20KHz

Output Impedance: 1 ohm (high gain) 0.3 ohm (low gain)

Gain: 8 (18db) or 1 (0db), selectable via panel switch

Topology: Tube voltage gain or solid-state tube voltage gain, cross-shunt push-pull Crossfet output stage, non inverting, single voltage gain stage

Inputs: One pair balanced XLR, one pair single-ended RCAs, switchable via front panel switch

Outputs: one 4-pin balanced female XLR, one 1/4 inch phono, one pair 3-pin male XLR preamp, one pair single-ended RCA

Power Consumption: 45W

Size: 30.6 x 22.3 x 6 cm

Weight: 5.4 kgs

*All measurements made on a Stanford Research SR1 or SR1+ Audio Analyser

    Bad           Good